Виджет отображает текущую температуру в градусах Цельсия, Фаренгейта, Кельвина. Для переключения между отображаемыми единицами нажмите START или тапните по экрану. Используется большой шрифт для отображения.</p><p></p><p>Виджет читает данные внутреннего датчика. Тепло тела влияет на датчик, поэтому отображается среднее значение между температурой тела и окружающей средой. Если вам нужно знать температуру окружающей среды, снимите устройство с вашего запястья. Подождите 10 минут, пока устройство не будет иметь температуру окружающей среды. Для некоторых устройств необходимо, чтобы к часам был подключен внешний датчик Tempe (то есть Forerunner 245, Gpsmap 66/86).</p>
1.9.9 - снова окончательно и навсегда удалена поддержка Edge Explore. Добавлено специальное сообщение, для устройств без встроенного датчика температуры. Для таких устройств необходим внешний датчик tempe.</p><p>1.9.6 - удалена поддержка Edge Explore (и Edge 1000, они выключаются вместе, официальное заявление Garmin - нет температурного датчика в Explore)</p><p>1.9.5 - добавлены новые устройства</p>
Данному приложению требуется доступ к следующей информации:
Przemysław Kaczorek
13 апреля 2021 г. | Версия 1.9.9
Działa z czujnikiem ANT, prawidłową temperatura pojawia się po ok. 30 sek.
Денисенко Роман
6 апреля 2021 г. | Версия 1.9.9
Это температура микросхемы, не окружающей среды. Соответсвеннено нет смысла от этих данных. Руку тоже не измеряет.
Paco Vigil
16 марта 2021 г. | Версия 1.9.9
Zachary Nikolayev
27 февраля 2021 г. | Версия 1.9.6
Pretty useless. Unless you have 10 min to wait around just to find out ambient temperature of your environment.
Agus Pianoman
21 февраля 2021 г. | Версия 1.9.6
It works fine. I take off my watch and, in a few minutes, it shows the same temperature as my weather station. Thank you!!
Pablo Sonder
16 февраля 2021 г. | Версия 1.9.6
Ответ разработчика
19 февраля 2021 г., Navicom
Read the description: "It reads at first the internal sensor data. Sensor is affected by the body heat so value is the average between your body tempearture and environment. If you need to know environmental temperature, take off the device of your wrist. Wait for 10 minutes until device will have the environment temperature." It is Garmin Hardware design. If you have any propositions and concerns - contact Garmin Support.
KAyers84
6 февраля 2021 г. | Версия 1.9.6
Downloaded it after checking to see if my watch was compatible....but its not supported after all.
Константин
2 февраля 2021 г. | Версия 1.9.6
Работает корректно. При сравнении с комнатным термометром совпадает до десятой градуса. До - 5°С работает точно. При более низкой температуре не проверял.
Alecroft
26 января 2021 г. | Версия 1.9.6
No funciona o estoy muerta porque si mi temperatura es de 30º o menos, sería imposible estarlo
Ответ разработчика
27 января 2021 г., Navicom
Read the description: "It reads at first the internal sensor data. Sensor is affected by the body heat so value is the average between your body tempearture and environment. If you need to know environmental temperature, take off the device of your wrist. Wait for 10 minutes until device will have the environment temperature." It is Garmin Hardware design. If you have any propositions and concerns - contact Garmin Support.
DK
16 января 2021 г. | Версия 1.9.6
Garmin Vivoactive 3. Seit 3 Tagen funktioniert das Widget nicht mehr.
Maciej Piecko
24 декабря 2020 г. | Версия 1.9.6
It is working with FR245 and Tempe ext. sensor only when currently connected to the sensor. Wigdet connects to the sensor automaticly every time its displayed and when widget is not visible it disconects from the sensor. The connection time is long, I have to wait a while to see the reading. I doubt if it is useful in that configuration.
Ответ разработчика
24 декабря 2020 г., Navicom
That is Garmin design and the way how the Tempe works internally - it lowers power consumption and broadcast information rarely. If you are electrical engineer, or have another ideas how to improve the situation - you can write garmin.com/ideas. Thank you for review.
Filippo
16 декабря 2020 г. | Версия 1.9.6
Takenya
23 ноября 2020 г. | Версия 1.9.5
This was weird. The site said it was compatible and I installed it. When I went to look for it, I found it but instead of a temperature, it said 'App is incompatible with this device'
Christian Clausen
19 ноября 2020 г. | Версия 1.9.5
Uploaded to Forerunner 720xt, but can not be found on device.
GEN 1A
17 ноября 2020 г. | Версия 1.9.5
Hier passiert nichts. Einstellungen zeigen nur die App Version an, nichts weiter. Ich mußte die Uhr booten, um die App zu installieren. Die Uhr zeigt weiterhin die falsche Temperatur an. Dafür hatte ich diese App nicht installieren müssen. Der gleiche Murgs, der schon werksseitig indtalliert war. Völlig unnötig. Ich hsb erwartet, daß ich hier ein Offset eingeben kann, um den Fehler, der durch die Körperwärme entsteht, auszugleichen.
Vasilis
6 ноября 2020 г. | Версия 1.9.5
I put my watch (fenix 6x) in the desk and i leave it 20 min.The measurement was to high,at least +4°C.
Утес
25 октября 2020 г. | Версия 1.9.1
Samantha Jones
16 октября 2020 г. | Версия 1.9.1
This doesn’t work for me there is no measurement displayed just a min empty red bar. I have the Garmin Fenix 5s
Naomi Tullos
6 октября 2020 г. | Версия 1.9.1
Its always in the 70°s, thermometer says im 98.7 , definitely not accurate
Ответ разработчика
7 октября 2020 г., Navicom
Variants: 1) Internal sensor is faulty. You need to replace your device. 2) SW obsolete. Update it via Garmin Express 3) Usage scenario does not fit the hardware capabilities. It reads at first the internal sensor data. Sensor is affected by the body heat so value is the average between your body tempearture and environment. If you need to know environmental tempearature, take off the device of your wrist. Wait for 10 minutes until device will have the environment temperature. Device cannot measure your body temperature precisely as medical thermometer (please do not expect 36.6 / 98.0). It is hardware limitations and device was designed for such usage. Developers cannot do anything with that, sorry.
Mikel Sasieta
10 сентября 2020 г. | Версия 1.9.1
garmin explorer, como a funcionado durante 2 años que tengo el gps? y ahora me venis con el cuento(You device does not have internal temperature sensor.) sospecho que sera marketing, pero no penseis que voy a cambiar el gps por eso.
Ответ разработчика
11 сентября 2020 г., Navicom
Please follow the Garmin support, not the 3rd party developers that use SDK provided by Garmin. We do not know why they removed functions from your device. Support for your device will be deleted from our app, we do not want more one-star ratings due to that, sorry.
Алексей
9 сентября 2020 г. | Версия 1.9.1
Pablo Vallés Urriza
3 сентября 2020 г. | Версия 1.7.1
Ya no funciona, podrian volver a poner la primera versión?, es la q funciona, muchísimas gracias
Ответ разработчика
4 сентября 2020 г., Navicom
Nothing was changed in the code since last update. Only Garmin software engineers can disable or enable features in your device. Why did they do that - we do not know. May be it is an issue, and you need to contact Garmin Support and assign new ticket to investigate. Also you can contact us and provide more details, like what is the device, sw installed on it. We will try to explain issue to Garmin.
Michael
17 августа 2020 г. | Версия 1.7.1
Reads and displays the data of the internal temperature sensor. No more, no less. Perfect. Thank you.
Sergio
6 августа 2020 г. | Версия 1.7.1
Извините, в настоящее время статистика недоступна.