== Support app development? ==</p><p></p><p>Do you like the datafield?</p><p>Feel free to make a donation on PayPal. Thanks to everyone supporting development.</p><p>https://paypal.me/winklerronny</p><p></p><p>== Overview ==</p><p></p><p>This datafield provides a graph showing the percentage of time spent in the defined power zones. The bars are growing depending on the time you spend in the zone during the activity.</p>
If you get problems after update (iq-Logo instead of datafield), please uninstall ans install the datafield again. That fixes most problems of changd app settings.</p><p></p><p>version 1.0.9</p><p>- excluded devices which don't support power sensors</p><p>version 1.0.8</p><p>- instead of possibility to show zone0, you can now choose to add values outside the zones to the lowest or highest zone.</p>
Ta aplikacja wymaga dostępu do następujących zasobów:
D2™ Bravo 
D2™ Bravo Titanium 
D2™ Charlie 
D2™ Delta 
D2™ Delta PX 
D2™ Delta S 
Edge® 1000 
Edge® 1030 
Edge® 1030, Bontrager 
Edge® 130 
Edge® 520 
Edge® 520 Plus 
Edge® 530 
Edge® 820 Edge® 830 
Edge® Explore 1000 
Edge® Explore 820 
epix™ 
ForeAthlete® 735XTJ 
ForeAthlete® 920XTJ 
Forerunner® 735XT 
Forerunner® 920XT 
Forerunner® 935 
Forerunner® 945 
fēnix® 3, quatix® 3, tactix® Bravo 
fēnix® 3 HR 
fēnix® 5, quatix® 5 
fēnix® 5 Plus 
fēnix® 5S 
fēnix® 5S Plus 
fēnix® 5X, tactix® Charlie 
fēnix® 5X Plus 
fēnix® Chronos Andreas Schrader
21 lipca 2019 | Wersja 1.0.8
Great Datafield. I've been using it for years. Just a little suggestion: Is it possible to spread the bars more evenly? I mean, zone 7 is a very big range (hundreds of watt). I takes most of the space of the datafield. But I hardly ride in Zone 7, but 2-4 instead. Please make all bars the same width!
Odpowiedź producenta
23 lipca 2019, ronnywinkler
It's already possible. Just change the low value your zones 1 and high value of your zone 7 to a value you want - so the bars get a wished width (e.g. same range like the zones 2 and 6. Then set the app option "Count only inside zones" to "off". The zones 1 and 7 are displayed smaller and all PWR values lower zone 1 will be added zu zone 1 and all PWR values higher that zone 7 will be added to zone 7. Please set the separate option for PWR-max ist you want to display the PWR-% based on PWR-max. It's calculated with this option and not with the high value of zone 7.
Manuel Antonio Gomez Mate
18 maja 2019 | Wersja 1.0.4-upd1
For me it is great. This is what I was looking for. Just a suggestion. It would be great if you can set the average time for Power instead fixed 3s to selectable between 1, 3, 5, and 10. More than 10 it is not very usefull. Regards, Manuel.
Luis Solaz
26 października 2018 | Wersja 1.0.4-upd1
Si se pudiese elegir el tiempo de la media además de 3s.que tuviese 10s. etc, estaría muy bien. Y si sólo indicando el FTP ya calculase las zonas.... sería perfecto.
Jörn Conrad
19 października 2018 | Wersja 1.0.4-upd1
Sehr gute Visualisierung meiner Leistungsdaten und auf dem 1030er permanenter Begleiter auf dem Rennrad. Vielen Dank an den Entwickler für die Mühe!!
Reed Griffith
28 stycznia 2018 | Wersja 1.0.2
just installed, has been working great! if there is an option to choose 5 or 10 second power smoothing with this app it would be nice to have.
Michael Gregory
24 lipca 2016 | Wersja 0.1.5-e8
This is just what I needed. Thank you so much! Works perfectly for me.
[민실용]김경민
28 czerwca 2016 | Wersja 0.1.3
I used the 0.1.1 version I had quite a problem. However, the 0.1.3 version seems to have resolved the problem. I do not speak English well, but I'm not as stupid as you think.
mcinner1
28 czerwca 2016 | Wersja 0.1.3
This app works as it's supposed to! No problems with Ant+ sensors! (here: Stages Powermeter and Wahoo HRsensor). (...and it's hard to believe that it might cause problems with sensor reception, because - I suppose - it establishes no connection to any sensor - just reads out data from your Edge)
Na razie brak dostźpnych danych.
Data Field