2018/10/23 | バージョン1.9-upd3
Best estimated power, is there a way to print on garmin connect best 20 min power??
2018/10/13 | バージョン1.9-upd3
resultats correct jusqu a la derniere mise a jour. depuis en montée resultats tres bas et proche de zero. que se passe t il?
2018/10/08 | バージョン1.9-upd3
This application is useless.
2018/08/26 | バージョン1.9-upd3
I thought at least this will be a good "live" estimate, especially going uphill but there must be some serious problems with the maths involved (or how data is provided by garmin). I would have liked the numbers displayed but strumbling around with 300 W on a recovery ride, pretty unrealistic...
I have a feeling that aerodynamic drag/rolling resistance is massively overestimated in standard configuration, e.g. going a bit downhill with no preassure on the pedals generated watt numbers around 250 W
To summarize: Better display hm/h and the gradient on your garmin to give you a feeling on how hard you are pressing the pedals, or get a powermeter...
2018/08/22 | バージョン1.9-upd3
there ara some strange peaks on descents
2018/07/29 | バージョン1.9-upd3
Since the last update, works normally in bump and on the flat. Thank you for this application. I recommend it. Thank you again for your work.
2018/07/11 | バージョン1.9-upd3
app doesn't work on climb or anytime that the gradient change...on climb goes to zero on descent calculate too much watt...works better till some months ago...but now unuseful
2018/05/07 | バージョン1.9-upd
Warning MTB fans, this app is based on speed, so for guys like me, is not useful, I had a power of 280 watts descending and 15 watts in a steep climbing. No make sense for MTB.
Is clear that the programmer did an excellent job for other kind of bikes,Road, Triathlon etc.
2018/05/05 | バージョン1.9-upd
pas de resultats coherents sur fenix 3hr ,meme au dessus de 40 TOURS MINUTES RESTE A 0
2018/04/17 | バージョン1.9-upd
I use this with a fixed gear bike and Garmin 520. It seems like the app doesn't recognize the grade of hills: going uphill (low cadence, slower speed) I get pretty low power estimates. Going downhill (sometimes 140+ cadence and 30+ mph) vPower is 450w+. That's the opposite of the power meter readings on my other bike. The app seems pretty accurate on flats and low grades. Any thoughts?
2018/04/13 | バージョン1.9
Thanks for a great app, great service from developer. Data very accurate. Thanks.!!
2018/04/01 | バージョン1.8.3
Works just perfekt. Very nice app. Thanks!
2018/03/28 | バージョン1.8.3
Works perfect. Gives a really good watt estimate on the ride, and all data is available in Garmin Connect afterwards. Great work :-)
2018/03/25 | バージョン1.8.3
Now with the peaks corrected is the best of the bes iq app for estimated power thanks a lot you save me a powermeter!!
2018/03/23 | バージョン1.8.2
I used to be quite happy with the data shown. But the new release with the “no cadence“ option does not make any sense at all. Is there a possibility to use the app without this nonsense?
Sorry for that Stephan. The calculation should however work correctly if a cadence sensor is connected.
2018/03/02 | バージョンVersion 1.8.1
Great for what it is, downloaded 5 different virtual power data field apps for my Fenix 3 hr, and tested against my Garmin power meter, and this was by far the most accurate and stable.
I just wish the data shown, could be uploaded to Connect with the rest of the ride data, is that even possible????
There has been a few issues, but looks like data is now uploading to GC.
Jaime Martín Granda
2018/02/13 | バージョン1.80-upd1
You also could match the values that calculate with BPM...
With BPM you have another way to calculale Power.
Maybe both inaccurate ways to calculate virtual power would be better tan one :) And decide if do an average or a weighted average towards one or another depending of the moment (Changes of bpms, altitude, cadence or so...)
As powercal, with a little TEST with a real power sensor at home (in the trainer) you could calibrate or ask for results to get BPM/power rates and so...
Then when going outside with any bike without power sensor, trying to estimate it better... In example for me at this moment, at constant efforts aprox:
167W - 115bpm
228W - 140bpm
274W - 159bpm
319W - 177bpm
365W - 185bpm
2018/01/31 | バージョン1.80
A few weeks ago. VPower only collect peaks of data while cycling. I replace the sensor but nothing happend. All other sensor on different bikes show the same result. What has happend ??
This should now be fixed.
2018/01/21 | バージョン1.80
Is ok in the flat route. During the climb it don't work beacuse don't read the % of slope and set wrong power ( normally from 10 to 70 watt max) . To calcolate the power the reading of the slope is necessary. I hope to use it with the next upgrade .
Slope is included in calculation, although it depends on the device accuracy also. I hope latest version shows better results.
2017/12/27 | バージョン1.80
I wonder if other have experienced it, but since the last update I am getting very low values - avg of 25W with a max of 65W...
Before the last update it was all working properly - the only difference is that I changed the average value to 10 seconds, I changed it back to 3 in the middle of the ride but it had no effect...
Before this update it was working really nice.. any idea?
2017/12/09 | バージョン1.80
It doesn't work on my edge 1030. I obtain amazing high power values descending, while power is close to 0 climbing. It seems that calculation is not taking into account my weight and/or bike's, although they are correctly set in my profile (me) and in the data field configuration (bike)
2017/11/28 | バージョン1.80
awesome, I use it since the day one, always improving..
the only problem, the beginning of the ride is very often a peak about 1000 watt or more, so the power graph on the website becomes less visible..
sometime I press the start button while moving on a flat road not pushing on pedals and it helps, but not always..
Do you want to send me the fit file so that I can see what parameters are causing the spike please?
2017/11/24 | バージョン1.80
Great update now it works and i think it´s very accurate a little bit overestimated on aceleration but when i see the fit in connect i see a peaks with 65500 watts i hope you can fix this thanks
Peaks in reading should now be fixed.
2017/11/21 | バージョン1.80
tq for providing the update. now successfully installed at my edge 520. contacted garmin supported previously they said might due to mine is taiwan version...
2017/11/17 | バージョン1.7.1-upd1
why it say apps not compatible when im trying to install at my edge 520 devices? pls help.
I released update 1.8 that should fix your problem.