Il widget visualizza la temperatura corrente in gradi Celsius, Fahrenheit, Kelvin. Per alternare tra le unità visualizzate, premere START o toccare lo schermo. Usa un font grande da visualizzare.</p><p></p><p>Legge i dati del sensore interno. Il sensore è influenzato dal calore corporeo, quindi il valore è la media tra la temperatura corporea e l'ambiente. Se hai bisogno di conoscere la temperatura ambientale, togli il dispositivo dal polso. Attendere 10 minuti fino a quando il dispositivo avrà la temperatura ambiente. Per alcuni dispositivi è necessario disporre di un sensore esterno Tempe collegato all'orologio (ad esempio Forerunner 245, Gpsmap 66/86).</p>
1.9.9 - Removed completely Edge Explore again. Added special message string for the devices without internal temperature sensor.</p><p>1.9.6 - Removed support for Edge Explore (among with Edge 1000, sorry, that is Garmin limitation, they said no temperature sensor in Explore)</p><p>1.9.5 - new devices added</p><p>1.9.1 - SDK 3.2.2, glances added</p><p>1.7.1 - SDK 3.1.9, new devices added</p><p>1.6.7 - SDK 3.1.7</p>
Questa app richiede l'accesso a:
Pollon
21 aprile 2021 | Versione 1.9.9
Przemysław Kaczorek
13 aprile 2021 | Versione 1.9.9
Działa z czujnikiem ANT, prawidłową temperatura pojawia się po ok. 30 sek.
Денисенко Роман
6 aprile 2021 | Versione 1.9.9
Это температура микросхемы, не окружающей среды. Соответсвеннено нет смысла от этих данных. Руку тоже не измеряет.
Paco Vigil
16 marzo 2021 | Versione 1.9.9
Zachary Nikolayev
27 febbraio 2021 | Versione 1.9.6
Pretty useless. Unless you have 10 min to wait around just to find out ambient temperature of your environment.
Agus Pianoman
21 febbraio 2021 | Versione 1.9.6
It works fine. I take off my watch and, in a few minutes, it shows the same temperature as my weather station. Thank you!!
Pablo Sonder
16 febbraio 2021 | Versione 1.9.6
Risposta sviluppatore
19 febbraio 2021, Navicom
Read the description: "It reads at first the internal sensor data. Sensor is affected by the body heat so value is the average between your body tempearture and environment. If you need to know environmental temperature, take off the device of your wrist. Wait for 10 minutes until device will have the environment temperature." It is Garmin Hardware design. If you have any propositions and concerns - contact Garmin Support.
KAyers84
6 febbraio 2021 | Versione 1.9.6
Downloaded it after checking to see if my watch was compatible....but its not supported after all.
Константин
2 febbraio 2021 | Versione 1.9.6
Работает корректно. При сравнении с комнатным термометром совпадает до десятой градуса. До - 5°С работает точно. При более низкой температуре не проверял.
Alecroft
26 gennaio 2021 | Versione 1.9.6
No funciona o estoy muerta porque si mi temperatura es de 30º o menos, sería imposible estarlo
Risposta sviluppatore
27 gennaio 2021, Navicom
Read the description: "It reads at first the internal sensor data. Sensor is affected by the body heat so value is the average between your body tempearture and environment. If you need to know environmental temperature, take off the device of your wrist. Wait for 10 minutes until device will have the environment temperature." It is Garmin Hardware design. If you have any propositions and concerns - contact Garmin Support.
DK
16 gennaio 2021 | Versione 1.9.6
Garmin Vivoactive 3. Seit 3 Tagen funktioniert das Widget nicht mehr.
Maciej Piecko
24 dicembre 2020 | Versione 1.9.6
It is working with FR245 and Tempe ext. sensor only when currently connected to the sensor. Wigdet connects to the sensor automaticly every time its displayed and when widget is not visible it disconects from the sensor. The connection time is long, I have to wait a while to see the reading. I doubt if it is useful in that configuration.
Risposta sviluppatore
24 dicembre 2020, Navicom
That is Garmin design and the way how the Tempe works internally - it lowers power consumption and broadcast information rarely. If you are electrical engineer, or have another ideas how to improve the situation - you can write garmin.com/ideas. Thank you for review.
Filippo
16 dicembre 2020 | Versione 1.9.6
Takenya
23 novembre 2020 | Versione 1.9.5
This was weird. The site said it was compatible and I installed it. When I went to look for it, I found it but instead of a temperature, it said 'App is incompatible with this device'
Christian Clausen
19 novembre 2020 | Versione 1.9.5
Uploaded to Forerunner 720xt, but can not be found on device.
GEN 1A
17 novembre 2020 | Versione 1.9.5
Hier passiert nichts. Einstellungen zeigen nur die App Version an, nichts weiter. Ich mußte die Uhr booten, um die App zu installieren. Die Uhr zeigt weiterhin die falsche Temperatur an. Dafür hatte ich diese App nicht installieren müssen. Der gleiche Murgs, der schon werksseitig indtalliert war. Völlig unnötig. Ich hsb erwartet, daß ich hier ein Offset eingeben kann, um den Fehler, der durch die Körperwärme entsteht, auszugleichen.
Vasilis
6 novembre 2020 | Versione 1.9.5
I put my watch (fenix 6x) in the desk and i leave it 20 min.The measurement was to high,at least +4°C.
Утес
25 ottobre 2020 | Versione 1.9.1
Samantha Jones
16 ottobre 2020 | Versione 1.9.1
This doesn’t work for me there is no measurement displayed just a min empty red bar. I have the Garmin Fenix 5s
Naomi Tullos
6 ottobre 2020 | Versione 1.9.1
Its always in the 70°s, thermometer says im 98.7 , definitely not accurate
Risposta sviluppatore
7 ottobre 2020, Navicom
Variants: 1) Internal sensor is faulty. You need to replace your device. 2) SW obsolete. Update it via Garmin Express 3) Usage scenario does not fit the hardware capabilities. It reads at first the internal sensor data. Sensor is affected by the body heat so value is the average between your body tempearture and environment. If you need to know environmental tempearature, take off the device of your wrist. Wait for 10 minutes until device will have the environment temperature. Device cannot measure your body temperature precisely as medical thermometer (please do not expect 36.6 / 98.0). It is hardware limitations and device was designed for such usage. Developers cannot do anything with that, sorry.
Mikel Sasieta
10 settembre 2020 | Versione 1.9.1
garmin explorer, como a funcionado durante 2 años que tengo el gps? y ahora me venis con el cuento(You device does not have internal temperature sensor.) sospecho que sera marketing, pero no penseis que voy a cambiar el gps por eso.
Risposta sviluppatore
11 settembre 2020, Navicom
Please follow the Garmin support, not the 3rd party developers that use SDK provided by Garmin. We do not know why they removed functions from your device. Support for your device will be deleted from our app, we do not want more one-star ratings due to that, sorry.
Алексей
9 settembre 2020 | Versione 1.9.1
Pablo Vallés Urriza
3 settembre 2020 | Versione 1.7.1
Ya no funciona, podrian volver a poner la primera versión?, es la q funciona, muchísimas gracias
Risposta sviluppatore
4 settembre 2020, Navicom
Nothing was changed in the code since last update. Only Garmin software engineers can disable or enable features in your device. Why did they do that - we do not know. May be it is an issue, and you need to contact Garmin Support and assign new ticket to investigate. Also you can contact us and provide more details, like what is the device, sw installed on it. We will try to explain issue to Garmin.
Michael
17 agosto 2020 | Versione 1.7.1
Reads and displays the data of the internal temperature sensor. No more, no less. Perfect. Thank you.
Sergio
6 agosto 2020 | Versione 1.7.1
Spiacenti, nessuna statistica disponibile al momento.