Stryd Zones | Data Field

Mario Gottburg
October 20, 2020 | Version V1.5

Works really fine

Leon Noel
October 15, 2020 | Version V1.5

Would be profoundly useful to add power zone alerts (which is crude but works) the same way the 80/20 datafield does for pace/HR. A vibration every time a transition between zones occurs, how hard can it be? It’s frustrating enough to keep looking at your watch during the entire course of the run, which also takes away the joy/focus. Run Power can do it, why can’t Stryd? Thanks.

Makkas CIQ
October 12, 2020 | Version V1.5

Can you please add a setting to disable vibration alert when stryd disconnects? Thanks.

Martin Strachota
September 14, 2020 | Version v1.4

Stryd is great and this datafield has always worked reliably for me (Fenix 3 and now Fenix 6X). However, I don't look at it at all - I only use it to write Stryd metrics to the FIT file. I use a different datafield to display power. In fullscreen mode, I would like this DF to display at least 3 metrics - instant power, lap power and lap time or distance. There's plenty of real estate on my Fenix display for that but this DF only shows 2 metrics.

Sammy Barguil
September 4, 2020 | Version v1.4

Lap power it's the same as the overall power. The connection between styrd and the watch sometimes transmit erroneous data.

David Higgins
September 4, 2020 | Version v1.4

Over the last couple of months the connection between my Fenix 5 and Stryd has just randomly failed. Used to be a perfect connection but not any longer. Using by and any connection options (non wind stryd)

Tassos Hantzakos
September 3, 2020 | Version v1.4

I am prompted to install it again and again each time I try to access the data fields from Garmin Connect. I have set it up as instructed for Fenix 6 Pro.

seb
August 29, 2020 | Version v1.4

Unreliable contrary to previous stryd power. Quite frustrating as the errors thst happen after a few seconds/minutes into the run render the whole activity data unusable by other systems.like trainingpeeaks that consider you did not move after the stryd error pops up (it bases stress score of activity on power data as such were given for few seconds and then no data means 0 power)

Mihai Stanciu
August 27, 2020 | Version v1.4

Does what it needs to do. Would be nice if zone in a small field was like garmins HR gauge.

Brian Reiter
August 26, 2020 | Version v1.4

The field works well and is reliable. The tiny zone number is not very readable in a field. Could you please add a linear or radial analog gauge? Like f6 radial HR gauge or HR Zones Chart CIQ field.

michelrebetez
August 18, 2020 | Version V1.3_

Ma fenix 6 pro n’affiche pas la Power zone, mais seulement la puissance ,

Laufsau77
August 6, 2020 | Version V1.3_

NO Zones on Fenix 6 Pro Solar

George Hellyer
July 26, 2020 | Version V1.2_

Good app but Can’t get the different colour zones to appear ?

Deb Lucas
July 10, 2020 | Version V1.2_

Cannot get the data field onto my Garmin 6s

Jose A. García Jiménez
July 8, 2020 | Version V1.2_

El Stryd no para de desconectarse todo el tiempo.

Jonathan
July 8, 2020 | Version V1.3

Stryd have mostly done an admiral job at a job that they should not have to do at this point (running power is natively supported in every other major running watch brand at this point). It is stable and does what it says it will. That said, the format of the field really leaves something to be desired. The "zones slider" on the left hand side just doesn't work as well as the standard zone gauge used by every other zones based field (Garmin native or CIQ). The graph/slider is difficult to see, which is presumably why they also used part of the field to print the zone number (you don't need to do that with the normal zone gauge). The other problem is that the zone slider only shows up if the Stryd Zones field is the only field shown on the watch. I have a heart rate zone field that shows me both my heart rate and the zone and it shares the screen with 5 other data fields...and it's actually easier to see at a glance. If the zones were easier to see they could also replace the zone number on the full screen field with % of Critical Power, which is how most of the Stryd power based training plans indicate training intensity. So, the general summary is that this data field does what it needs to well from a functional standpoint, but could really use a better display setup.

Nick
June 23, 2020 | Version V1.2

The Stryd zones data field is great for always running with your auto cp zones. The ability to have a primary and secondary power metric is sweet!

Jamie Stuart
June 19, 2020 | Version Feb 19, 2020 - 2

For short runs it’s great and the graphs are very informative. However earlier this year I ran an Ultramarathon, and despite switching bluetooth off and removing the sensor from my Fenix 5, the watch still tried searching for the power meter and it drained the battery within 3/4 of the race.

Stuart
June 11, 2020 | Version Feb 19, 2020 - 2

Good, but would be great if you could include other fields (heart rate, distance, time etc) so that the zones graph at the left side could still be viewed on the same screen as power & distance (or other standard field). The other option is to use multiple fields on the watch itself, but the power zone graph on the left hand side only appears to be there when one a single field (i.e. the Stryd field) is used

Gene
May 16, 2020 | Version Feb 19, 2020 - 2

Other than numerical zone switch not working on a small version of the power field (zone number still stays on the top, it's a shame, if you can't disable it at least move it to the side and make power numer bigger, it's hard to read on the run) and it having wrong description (select to display your real time zone?!) everything works as it should. I'll give it a solid 5 and hope above-mentioned will get swiftly fixed ;)

olimpodelsol
May 10, 2020 | Version Feb 19, 2020 - 2

Por favor ponerlo también en español, no se ingles y me pierdo con la información q me dan. Muchas gracias

Arweth
April 19, 2020 | Version Feb 19, 2020 - 2

Usually logs the data (As long as the field is enabled on one of the screens on the watch and you dont forget about charging it). However the screens don't display on a Venu watch. You get a tiny indication of the power meter on the left of the display and nothing else. This is setup as per the documentation with a single field layout and stryd configured for the field.

Paul Vinh
April 5, 2020 | Version Feb 19, 2020 - 2

Was working great until 2 updates ago. Now when I try to use this version, after running for 3 minutes the data field would show and an error and stop collecting stryd data into my watch

bowlsie
March 22, 2020 | Version Feb 19, 2020 - 2

fenix 6x pro using zones. tried the new beta version of stryd but no luck with that :-) zones works perfectly as is. set up easy. thx

Diki
February 21, 2020 | Version Feb 19, 2020 - 2

Pleas add the option for 1 and 2 minute average power for the secondary display.